Frymaster FOOTPRINT RE80 Manuel d'utilisateur

Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1-

1-5 2. On dual-vat fryers, and on full-vat fryers where the temperature probe is attached to the element being replaced, disconnect the wire harness

1-6 1425361425367895R4R6R1R2R3RIndex Marker marks Position 15L 4L6L 1L2L3L 9. Reconnect the element connector ensuring that the latches lock. 10. In

1-7 guide rails (see photo below). The contactor boxes of non-filter units or frypots not over the filter pan are accessed by opening the fryer door

1-8 14. Remove the covers from the drain safety switch(es) and disconnect the switch wiring at the switch(es). 15. At the rear of the fryer, unplug t

1-9 1.9 Built-in Filtration System Service Procedures 1.9.1 Filtration System Problem Resolution One of the most common causes of filtration pro

1-10 Disconnect power to the filter system, remove the input plumbing from the pump, and use a screwdriver to manually turn the gears. ● Turning the

1-11 6. When complete, reverse steps to reinstall the bridge. NOTE: The black motor wires go on the top terminal, the white on the bottom. The pump

1-12 100-120V Configuration208-250V Configuration1.10 Basket Lift Service Procedures High Production RE Series electric fryers may be equipped with

1-13 BINDING/JAMMING PROBLEMS Noisy, jerky or erratic movement of the lifts is usually due to lack of lubrication of the rods and their bushings. Ap

1-14 1.11 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a mult

i NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED

1-15 1.12 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. F OHMS C F OHMS C

1-16 1.13 Wiring Diagrams 1.13.1 Basket Lift

1-17 1.13.2 PBI Basket Lift

1-18 1.13.3 Standard Component Wiring

1-19 1.13.4 Component Wiring – Single Phase 805-1786

1-20 1.13.5 Component Wiring – 480V Non-Filter 805-1776

1-21 1.13.6 Component Wiring - Fast Ready

1-22 1.13.7 Component Wiring – KFC-1

1-23 1.13.8 Contactor Box – Domestic, 17 kW 1.13.9 Contactor Box – Domestic, 21 kW

1-24 1.13.10 Contactor Box – Export

ii DANGER Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical condu

2-1 E4 SERIES HIGH PRODUCTION RE ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 345678912 ITEM PART # COMPONENT 1 809-0985 Thumbscr

2-2 2.2 Cabinetry 2.2.1 Back Panels, Tilt Housings, Top Caps, and Doors

2-3 2.2.1 Back Panels, Tilt Housings, Top Caps, and Doors (cont.) ITEM PART # COMPONENT 1 Back, Cabinet Standard 220-5033 x1 220-5034 x2,

2-4 2.2.1 Back Panels, Tilt Housings, Top Caps, and Doors (cont.) ITEM PART # COMPONENT FAST 106-8427 x1 106-7166 x2 6 Computer Bezel

2-5 2.2.2 Cabinets, Bases, Braces, and Associated Parts (FINAL) 4220581318171615614119119123710 ITEM PART # COMPONENT 1 Base Assembly 106-8

2-6 2.2.2 Cabinets, Bases, Braces, and Associated Parts cont. ITEM PART # COMPONENT Cabinet Sides 4 231-4896 Side, Stainless Steel, Left 5 23

2-7 2.2.3 Basket Lift Assembly and Associated Parts 282625127222110216111754 171724320314181298171529303334353231

2-8 2.2.3 Basket Lift Assembly and Associated Parts (cont.) ITEM PART # COMPONENT 106-3775 Basket Lift Assembly, 100-120VAC 106-4147 Basket Lift

2-9 2.3.1 Filter Pan Assemblies 7891061234511121211Multi-vat Filter AssemblySingle-vat Filter Assembly

2-10 2.3.1 Filter Pan Assemblies (cont.) ITEM PART # COMPONENT 106-7674SP Filter Assembly, Multi-vat, Paper Filtration 1 823-6943 Lid, Filter Pa

iiiE4 SERIES HIGH PRODUCTION RE ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS ...

2-11 2.3.2 Filter Pump ITEM PART # COMPONENT 1 Filter Pump Components 816-0093 Pump Gasket 810-3347 8GPM Pump 826-1264 4 GPM Pump 826-

2-12 2.4 Drain System Components 2.4.1 Drain Valve Assemblies 541326118910108-017912810-2126121513141617108-0124182522202123262419108-1999 &

2-13 2.4.1 Drain Valve Assemblies (cont.) ITEM PART# COMPONENT Drain Valve (units equipped with filtration) 1 810-2783 Valve, 1 ½” Full Port 2

2-14 2.4.2 Drain System Plumbing ITEM PART# COMPONENT Drain Plumbing With Drain Flush 27 812-2078 Downspout, Center 28 823-4681 Right,

2-15 2.5 Oil Return System Components 20123971068115412181513191416

2-16 2.5 Oil Return System Components (cont.) ITEM PART # COMPONENT 1 Oil Return Plumbing Assembly 106-9711 Left Assembly 106-9712 Right Assemb

2-17 2.5.1 Oil Disposal Wand 12345 ITEM PART # COMPONENT 108-0528 Oil Disposal Wand Assembly 1 106-1454 Nozzle assembly with handle 2 810-14

2-18 2.5.2 Over-the-Top Oil Return (KFC) ITEM PART # COMPONENT 106-9693 Plumbing Assembly 1 810-3468 Tubing, Over the Top 2 810-2513 Tub

2-19 2.5.3 Drain Flush Plumbing ITEM PART # COMPONENT 1 106-4006 Valve Assembly, Oil Return, 1/2" 2 200-8929 Handle, Oil Return 3 809-

2-20 2.6 Heating Element Assemblies and Associated Parts 2.6.1 Element Assemblies and Hardware NOTE: These elements apply only to the RE series

ivE4 SERIES HIGH PRODUCTION RE ELECTRIC FRYERS TABLE OF CONTENTS (cont.) 2.6 Heating Elements ...

2-21 2.6.1 Heating Element Assemblies and Associated Parts (cont.) ITEM PART # COMPONENT 1 Element Assemblies 106-9757 208V, 17kW 106-9974 20

2-22 2.6.2 Element Tube Assemblies ITEM PART # COMPONENT 106-7653SP Tube Assembly RE Element, Full-Vat 1 106-5329 Bracket Assembly, LH Elem

2-23 2.7 Frypot Assemblies and Associated Parts ITEM PART # COMPONENT 1 Frypot Assembly 823-6935SP Frypot, Non-filter 823-6721SP Frypot, Fi

2-24 2.8 Controllers ITEM PART # COMPONENT Computers 1 826-2429 Computer Magic III.5, Full-Vat, non-CE * 106-4343 Computer Magic I

2-25 2.9 Electronics and Wiring Components 2.9.1 Component Boxes

2-26 2.9.1 Component Boxes ITEM PART # COMPONENT Component Box Assemblies (for reference) 106-9730 208/240V, Filter 106-9732 208/240V, Non

2-27 2.9.2 Contactor Boxes

2-28 NOTES: Left and right contactor box assemblies are mirror images of one another. With the exception of the box itself, most components of a left-

2-29 2.9.3 Fuse Boxes 312457681091112Left 22kW andSingle Phase Fuse Box Assembly106-5505/106-6678Right 22kW andSingle PhaseFuse Box Assembly106-5506

2-30 2.9.4 Terminal Blocks ITEM PART # COMPONENT 1 823-5631 Box, LH Rear Terminal Block 2 823-5632 Box, RH Rear Terminal Block 823-5797 Bo

1-1 E4 SERIES HIGH PRODUCTION RE ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frymaster f

2-31 2.9.5 Cordsets ITEM PART # COMPONENT * 807-4658 Domestic * OPT11295 Generic Export * OPT37413 Church’s Cord Connect Box * Not illustrated.

2-32 2.10.2 Component Box, Filter Pump and Basket Lift Wiring Harnesses ITEM PART # COMPONENT 1 106-9930 Component Box Harness, Filter 2

2-33 2.11 Wiring Connectors and Pin Connectors ITEM PART # COMPONENT 1 807-1068 2-Pin Female 2 807-0158 6-Pin Female 3 807-0156 9-Pin Female 4 8

2-34 2.12 Fasteners ITEM PART # COMPONENT * 809-0429 Bolt, ¼-inch – 20 x 2.00-inch Hex Head ZP Tap * 809-0514 Capscrew, 5/16-inch-18 NC Hex * 80

Frymaster, L.L.C., 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-318-219-7140 (Tech Support) 1-318-219-7135 PRIN

1-2 NOTE: If more room to work is required, the control panel frame assembly may be removed by removing the hex head screws that secure it to the fr

1-3 4. Locate the high-limit that is being replaced and follow the two-black wires to the 12-pin connector C-6. Note where the leads are connected p

1-4 5. Raise the element and remove the securing probe bracket and metal tie wraps that secure the probe to the element (see illustration below).