Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1

1-6 8. Reconnect the element connector ensuring that the latches lock. 9. Insert the temperature probe leads into the 12-pin wiring harness connect

1-7 5. Unplug the elements wires (white wires with plugs) inside component box. 6. Remove the lid. 7. Remove the screw (white arrows below) from

1-8 2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the front and rear. 3. Slide the metal bezel

1-9 21. Position the element tube assembly in the frypot and reinstall the machine screws and nuts removed in Step 14. 22. Reconnect the oil return f

1-10 If the pump starts after resetting the thermal overload switch, then something is causing the motor to overheat. A major cause of overheating is

1-11 2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the front and rear. 3. Disconnect the flexli

1-12 10. Reconnect the unit to the electrical power supply, and verify that the pump is functioning correctly (i.e., when a filter handle is placed in

1-13 1.10 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a mult

1-14 1.11 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. F OHMS C F OHMS C

1-15 1.12 Component Wiring 1.12.1 Standard Wiring YFPRE

i NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED

1-16 1.12.2 Tilt Switch Wiring 1.12.3 Terminal Block Wiring

1-17 1.12.4 Contactor – DELTA Configuration, 3 Phase MERCURY CONTROLS CIRCUIT

1-18 1.12.5 Contactor – Single Phase

2-1 YFPRE SERIES ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 1234 ITEM PART # COMPONENT 1 803-0366 Basket, 4-Lane Cooking 2 106-9

2-2 2.2 Cabinetry

2-3 2.2 Cabinetry (cont.) ITEM PART # COMPONENT 106-9311 Cabinet Assembly 1 106-9431 Upright Assembly, LT Enclosure 2 106-9432 Upright Assembl

2-4 2.3 Drain Components ITEM PART # COMPONENT 106-9351 Drain Valve Assembly 1 106-6020 Bracket, Assembly, 1-1/4" Drain Valve Micros

2-5 2.4 Electronics and Wiring Components 2.4.1 Heating Elements and Associated Parts ITEM PART # COMPONENT 1 826-2557 Element Kit, 208V (in

2-6 2.4.2 Tilt Switch Assembly ITEM PART # COMPONENT 1** 106-5876SP Sensory Assembly, Magnetic Positioning 2** 810-3007 Magnet, Magneti

2-7 2.4.3 4-Lane Controller ITEM PART # COMPONENT 1 106-9353 Wingstreet 4-lane Computer * 108-1253 Wingstreet 4-lane Computer (for Canadia

ii DANGER Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical condu

2-8 2.4.4 Contactor Box ITEM PART # COMPONENT 1 106-6031 Harness Assembly, Contactor Box Control, 12 Pin 2 106-6799 Harness Assembly, 20

2-9 2.4.5 Component Box ITEM PART # COMPONENT 1 826-2260 PCB Assembly, Interface Board, SMT 2 807-0979 Transformer, 208/240/12VAC, 50/60 Hz, 4

2-10 2.5 Wiring 2.5.1 Contactor Box Harness Assembly, 12-Pin (Control) 2.5.2 Contactor Box Harness Assembly, MDI, 6-Pin (Left Element) BL

2-11 2.5.5 Main Wiring Harnesses 2.5.6 Component Box and Filter Pump 12 ITEM PART # COMPONENT 1 106-5750SP Full Vat Control Harness J4

2-12 2.6 Filtration System Components

2-13 2.6 Filtration System Components (cont.) ITEM PART # COMPONENT 106-9313 Filter Pan Assembly 1 823-7086 Filter Pan 2 220-4446 SanaGrid Fil

2-14 2.7 Frypot and Associated Parts 125643789Front of Frypot ITEM PART # COMPONENT Frypot Assembly 1 823-6706 Frypot 2 807-0128 Bushing,

2-15 2.8 Wiring Connectors and Pin Connectors ITEM PART # COMPONENT 1 807-1068 2-Pin Female 2 807-2136 6-Pin Female, Hi Amp 3 807-2138 9-Pin

2-16 2.9 Fasteners (Nuts, Bolts, Screws, Washers) ITEM PART # COMPONENT * 809-0514 Capscrew, 5/16-inch-18 NC Hex * 809-0448 Clip, Tinnerman * 8

THIS PAGE INTENTIONALLY LEFT BLANK

iiiYFPRE SERIES ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS...

Frymaster, L.L.C 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-318-219-7140 (Tech Support) 1-318-219-7135 819-64

1-1 YFPRE SERIES ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frymaster fryer, disconnect

1-2 3. Remove the two screws from the upper corners of the control panel and allow the control panel to swing down. 4. Unplug the wiring harness fr

1-3 3. Remove the four screws from both the left and right sides of the lower back panel. 4. Locate the high-limit that is being replaced and follo

1-4 5. Raise the element and remove the securing probe bracket and metal tie wraps that secure the probe to the element (see illustration below).

1-5 1.6 Replacing a Heating Element 1. Perform Steps 1-3 of section 1.5, Replacing a Temperature Probe. 2. On full-vat fryers where the temper