Frymaster Enodis MRE14 SERIES Manuel d'utilisateur

SERVICE MANUAL FRYMASTER BIRE14/MRE14 SERIES ELECTRIC FRYER Frymaster L.L.C., 8700 Line Avenue 71106 P.O. Box 51000, Shreveport, Lou

1-2 3. Remove the two screws from the upper corners of the control panel and allow the control panel to swing down. 4. Unplug the wiring harness f

1-3 1.4 Replacing a High-Limit Thermostat 1. Remove the filter pan and lid from the unit. Drain the frypots into an McDonald’s Shortening Dispos

1-4 2. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of the fryer. 3. Remove the four screws

1-5 10. Secure any loose wires with wire ties making sure that the lead wires will not interfere with the movement of the springs. Rotate the element

1-6 leads in place. NOTE: It is critical that the wires be routed through the sleeving to prevent chafing. 1425361425367895R4R6R1R2R3RIndex Marker

1-7 2. Disconnect the fryer from the electrical power supply. 3. Remove the two screws securing the cover of the contactor box. The contactor boxes

1-8 3. Slide the metal bezel up to release the bottom tabs, then slide the bezel down to disengage the upper tabs. 4. Remove the two screws from th

1-9 22. Position the element tube assembly in the frypot and reinstall the machine screws and nuts removed in step 14. 23. Reconnect the oil return f

1-10 If the pump motor overheats, the thermal overload will trip and the motor will not start until it is reset. If the pump motor does not start, pr

1-11 DANGER DO NOT drain more than one full frypot or two split frypots into the MSDU at one time. 2. Disconnect the fryer from the electrical pow

NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRE

1-12 10. Reconnect the unit to the electrical power supply, and verify that the pump is functioning correctly (i.e., when a filter handle is placed i

1-13 1.10 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a multi

1-14 1.11 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. F OHMS C F OHMS C F

1-15 1.12 Wiring Diagrams 1.12.1 Component Wiring

1-16 1.12.2 Tilt Switch Wiring

1-17 1.12.3 Contactor Box – Delta Configuration

1-18 1.12.4 Contactor Box – WYE Configuration MERCURY ELEMENT WIRINGMERCURY CONTROLS CIRCUITEPRI/TRIAC SSR ELEMENT/CONTROLS WIRING

1-19 1.12.5 Simplified BIRE/MRE14 Series – Full Vat Delta Wiring

1-20 1.12.6 Simplified BIRE/MRE14 Series – Dual Vat Delta Wiring

1-21 1.12.7 Simplified BIRE/MRE14 Series – Full Vat Wiring EXPORT WYE ELECTRIC BIRE/MRE14 SERIES - FULL-VAT EXPORT 24VHIGH LIMITDRAIN SAFETYSWITC

DANGER Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause property damage, injury, or

1-22 1.12.8 Simplified BIRE/MRE14 Series – Dual Vat Wiring EXPORT WYE ELECTRIC BIRE/MRE14 SERIES - DUAL-VAT EXPORT 3 PHASE POWER TERMINALSGNDLATCH

1-23 1.12.9 Simplified BIRE/MRE14 Series – Full Vat Wiring EPRI

1-24 1.12.10 Simplified BIRE/MRE14 Series – Full Vat Wiring EPRI EXPORT WYE

2-1 BIRE14/MRE14 SERIES ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 3456789101112 ITEM PART # COMPONENT 1 809-0171 Thumbscrew, ¼ -2

2-2 2.2 Cabinetry 2.2.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings, and Top Caps 114151617234561311108127L7R8

2-3 2.2.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings, and Top Caps ITEM PART # COMPONENT 1 Back Panel, Upper (Panel for f

2-4 2.2.2 Cabinets, Bases, Braces, and Associated Parts See Page 2-34 for rear bridge support/oil return manifold. See Page 2-28 for filter rails an

2-5 2.2.2 Cabinets, Bases, Braces, and Associated Parts cont. ITEM PART # COMPONENT 1 106-3828 Upright Assembly, Left 2 106-3829 Upright Assembl

2-6 2.3 Drain System Components 2.3.1 Drain Tube Sections and Associated Parts 87766133445221 See next section for Drain Valves

2-7 2.3.1 Drain Tube Sections and Associated Parts cont. ITEM PART# COMPONENT 1 Drain Tube, Left/Right End Short 823-4625 Full-Vat 823-4624 D

ii WARRANTY STATEMENT Frymaster, L.L.C. makes the following limited warranties to the original purchaser only for this equipment and replacement part

2-8 2.3.2 Drain Valves and Associated Parts (Units with Built-In Filtration) 123456789101112Single Footprint Full-Vat Drain Valve Assembly 106-6300

2-9 2.3.2 Drain Valves and Associated Parts (Units with Built-In Filtration) cont. 2.3.2 Drain Valves and Associated Parts (Units with Built-In

2-10 2.3.2 Drain Valves and Associated Parts (Units with Built-In Filtration)

2-11 2.3.2 Drain Valves and Associated Parts (Units with Built-In Filtration) cont. ITEM PART # COMPONENT 1 816-0639 Cap, Drain Handle 2 809-

2-12 2.3.3 Drain Valves and Associated Parts (Units without Built-In Filtration) 12345 ITEM PART # COMPONENT 1 810-1569 Valve, 1.25-inch Non-F

2-13 2.4 Electronics and Wiring Components 2.4.1 Component Boxes 208-240V NON-CE Boxes 120V, 440 and 480V Boxes208-240V CE Boxes NOTE 1: The tran

2-14 2.4.1 Component Boxes cont. ITEM PART # COMPONENT 1 106-5592 Box Assembly, Component 2 200-3300 Bracket, Component Box Strain Relief 3 8

2-15 2.4.2 Contactor Boxes 2.4.2.1 Left and Right Over the Filter Pan Contactor Box Configurations

2-16 2.4.2.1 Left and Right Over the Filter Pan Contactor Box Configurations NOTES: Left and right contactor box assemblies are mirror images of one

2-17 2.4.2.2 Large Center Contactor Box Configurations (Non-Filter, Not Over the Filter and Single Units) STANDARD 14kW CONFIGURATIONTRIAC 14kW CON

iii E. PARTS RETURN All defective in-warranty parts must be returned to a Frymaster Authorized Factory Service Center within 60 days for credit. Af

2-18 2.4.2.2 Large Center Contactor Box Configurations (Non-Filter, Not over the Filter and Single Units) cont. ITEM PART # COMPONENT 1 106-6081

2-19 2.4.3 Terminal Blocks ITEM PART # COMPONENT 1 823-5631 Box, LH Rear Terminal Block 2 823-5632 Box, RH Rear Terminal Block 3 220-0801

2-20 2.4.4 Heating Element Assemblies and Associated Parts 2.4.4.1 Element Assemblies and Hardware NOTE: These elements apply only to RE seri

2-21 2.4.4.1 Element Assemblies and Hardware cont. ITEM PART # COMPONENT 1 Element 826-2198 200V 17.0 kW 826-2192 208V 17.0 kW 826-2200 220V

2-22 2.4.4.2 Element Tube Assemblies

2-23 2.4.4.2 Element Tube Assemblies contd. ITEM PART # COMPONENT 1 106-7653SP Tube Assembly RE Element, Full-Vat 2 106-7654SP Tube Assembly

2-24 2.4.6 Wiring 2.4.6.1 Contactor Box Wiring Assemblies – 12-Pin Dual-Vat C-1 2ORANGE 71C123456789101112ORANGE 72CYELLOW 184C1GREEN/YELLOW 75CBL

2-25 2.4.6.2 Contactor Box Wiring Assemblies – 12-Pin Full-Vat C-1 ITEM PART # COMPONENT 106-6031 Contactor Box Harness Assembly Full Vat 1

2-26 2.4.6.3 Contactor Box Wiring Assembly – 6-Pin (Left Element) ITEM PART # COMPONENT 1 106-6768 14/17 kW Mercury Contactor 2 106-6771 14/1

2-27 2.4.6.5 Main Wiring Harnesses USED ONLY ON DUAL VAT HARNESSESJ4C1C6C6C1J4J4C1C6FULL VAT HARNESS807-4194DUAL VAT HARNESS807-419512-Pin Female

iv ELECTRICAL POWER SPECIFICATIONS VOLTAGE PHASE WIRE SERVICE MINIMUM WIRE SIZE AWG (mm) AMPS (per leg) 208 Single 3 3 (5.83) 68 208 3 3

2-28 2.4.6.6 Component Box and Filter Pump Wiring Harnesses 123 ITEM PART # COMPONENT 1 106-5750 Full Vat Control Harness J4 to J2 (Standard)

2-29 2.4.6.8 Interface Board to Controller Wiring Harness – 15-Pin PN 807-4199SMT Controller to Interface Board Wiring Harness

2-30 2.5 Filtration System Components

2-31 2.5 Filtration System Components cont. ITEM PART # COMPONENT * 826-1979 Filter Pan Roller Kit (four each of Items 7 and 8) * 826-1980 Servic

2-32 2.5 Filtration System Components cont. ITEM PART # COMPONENT 18 807-2484 Valve, ¼-inch Solenoid 19 810-2493 Fitting, ¼-inch x 90° Quick-Con

2-33 2.6 Frypot Assemblies and Associated Parts 1234 56666777778810911

2-34 2.6 Frypot Assemblies and Associated Parts cont. ITEM PART # COMPONENT 1 Frypot Assembly (does not include Item 6) 2 823-5545SP Frypot, Ful

2-35 2.7 Oil Return System Components

2-36 2.7 Oil Return System Components cont. ITEM PART # COMPONENT 1 106-2465SP Handle Assembly, Full-Vat and Right Dual-Vat Rear Flush Complete 2

2-37 2.8 Wiring Connectors, Pin Terminals, and Power Cords ITEM PART # COMPONENT Power Cords * 807-0154 100/120V–15A 3-wire, w/grounded plug

v BIRE14/MRE14 SERIES E4 ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS...

2-38 2.9 Fasteners ITEM PART # COMPONENT * 809-0429 Bolt, ¼-inch – 20 x 2.00-inch Hex Head ZP Tap * 809-0514 Capscrew, 5/16-inch-18 NC Hex * 809-

THIS PAGE INTENTIONALLY LEFT BLANK

Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000 Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106

vi BIRE14/MRE14 SERIES E4 ELECTRIC FRYERS TABLE OF CONTENTS cont. 2.4.6.4 Contactor Box Wiring Assemblies 9-Pin Right Element...

1-1 BIRE14/MRE14 SERIES ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frymaster fryer, dis