Frymaster Pro H55-Series Manuel d'utilisateur

Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1-

2-2 One of the most important considerations of efficient fryer operation is ventilation. Make sure the fryer is installed so that products of combus

2-3 DANGER This appliance requires electrical power for operation. Place the gas control valve in the OFF position in case of a prolonged power outa

2-4 2. Single unit fryers must be stabilized by installing restraining chains on fryers equipped with casters or anchor straps on fryers equipped wit

2-5 Non-CE Standardfor Incoming Gas PressuresGas Minimum MaximumNatural6" W.C.fPa

2-6 Gas Connection Pipe Sizes(Minimum incoming pipe size should be 1 1/2" (41 mm))Natural3/4" (22 mm)1" (28 mm) 1 1/4" (36 mm)Prop

2-7 1. Connect the quick-disconnect hose to the fryer quick-disconnect fitting under the front of the fryer and to the building gas line. NOTE: Som

2-8 Non-CE StandardBurner Manifold Gas PressuresGas PressureNatural3" W.C.0.73 kPaPropane8.25" W.C.2.5 kPa 5. Check the programmed temper

2-9 CE GAS CONVERSION INSTRUCTIONS 1. Between G20- and G25-type Natural Gas, adjust the gas pressure at the regulator. (Refer to the CE Standard Bur

THIS PAGE INTENTIONALLY LEFT BLANK

3-1 PRO H55 SERIES GAS FRYER CHAPTER 3: OPERATING INSTRUCTIONS 3.1 Controller Operation and Programming Pro H55 Series gas fryers can be equipped

THIS PAGE INTENTIONALLY LEFT BLANK

3-2 Lighting the Fryer 1. Press the computer/controller ON/OFF switch to the OFF position. HoneywellONOFFHoneywellONOFFFor Non-CE FryersAfter placin

3-3 the motor is a plate with a locking nut. Loosen the nut enough to allow the plate to be moved, then adjust the position of the plate to open or c

THIS PAGE INTENTIONALLY LEFT BLANK

4-1 PRO H55 SERIES GAS FRYERS CHAPTER 4: FILTRATION INSTRUCTIONS WARNING The on-site supervisor is responsible for ensuring that operators are made

4-2 DANGER NEVER attempt to clear a clogged drain valve from the front of the valve! Hot oil will rush out creating the potential for severe burns.

4-3 4.2.1 Preparation for Use with Filter Paper or Filter Pad 1. Pull the filter pan out from the cabinet and remove the crumb tray, hold-down rin

4-4 5. When the hold-down ring is in position, if using filter paper, sprinkle one cup of filter powder evenly over the paper. (See Figure 4) If u

4-5 4. Replace the Magnasol filter assembly in the filter pan, ensuring that the fitting on the bottom of the assembly is securely seated in the por

4-6 2. Install the Power Shower. NOTE: Verify that the Power Shower O-ring and gasket are present and in good condition and that the clean-out s

4-7 WARNING The filter pump is equipped with a manual reset switch in case the filter motor overheats or an electrical fault occurs. If this switch

ii NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED D

4-8 4.4 Disassembly and Reassembly of the Magnasol Filter Dissassembly 1. Grasp the frame with your thumbs on the handles at the corner of the ass

4-9 Steps 1 and 2 - Stack outer screensand insert edges into frame.Step 3 - Insert grid between screensafter screens have been positioned inframe.Step

4-10 4.6 Using the Optional Rear-Discharge Oil Disposal 1. Ensure the filter pan is clean and ready for filtering. DO NOT discharge oil through a

5-1 PRO H55 SERIES GAS FRYERS CHAPTER 5: PREVENTIVE MAINTENANCE 5.1 Fryer Preventive Maintenance Checks and Service DAILY CHECKS AND SERVICE Ins

5-2 4. Set the thermostat to 195ºF (91ºC) or program the computer for Boil-Out (see separate Frymas-ter Fryer Controllers User’s Manual) and simmer

5-3 MONTHLY CHECKS AND SERVICE Check Calibration of Analog Controller Thermostat Control Knob (This check applies only to units equipped with Anal

5-4 QUARTERLY CHECKS AND SERVICE Clean Combustion Air Blower Assembly 1. Disconnect the blower wiring harness and remove the four blower mounting

5-5 4. Remove the plastic wrap from the blower motor assembly. Reassemble the blower motor assembly and blower housing. Reinstall the blower asse

5-6 SEMI-ANNUAL CHECKS AND SERVICE Clean Gas Valve Vent Tube NOTE: This procedure is not required for fryers configured for export to CE countries.

5-7 CLEAN-OUT PLUGSGASKETO-RING Immediately after each use, drain the Power Shower completely. If oil is leaking at the point where the Power Showe

iii DANGER No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call th

5-8 • Verify that component box components (i.e. computer/controller, transformers, relays, interface boards, etc.) are in good condition and free

6-1 PRO H55 SERIES GAS FRYERS CHAPTER 6: OPERATOR TROUBLESHOOTING 6.1 Introduction This chapter provides an easy reference guide to some of the comm

6-2 6.2 Troubleshooting Fryers with Computer Magic III.5, Basket Lift Timer, or Digital Controller PROBLEM PROBABLE CAUSES CORRECTIVE ACTION A.

6-3 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION A. Failed computer/controller. A. If available, substitute a computer/controller known to be workin

6-4 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION Heat indicator off upon initial startup. Display shows or with alarm sounding. Failed computer/co

6-5 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION A. Failed controller. A. If available, substitute a controller known to be working for the suspect

6-6 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION Heating mode light is ON with power switch in OFF position. After initial startup, fryer continues t

6-7 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION (Continued from previous page.) C. Pump blockage. Test: Close the drain valve. Place the filter ha

6-8 PROBLEM PROBABLE CAUSES CORRECTIVE ACTION (Continued from previous page.) C. Missing paper in filter pan. (This causes too much pressure in t

THIS PAGE INTENTIONALLY LEFT BLANK

1-1 PRO H55 SERIES GAS FRYER CHAPTER 1: GENERAL INFORMATION 1.1 Applicability and Validity The Pro H55 Series Gas Fryer has been approved by the E

Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000 Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106

1-2 1.3 Safety Information Before attempting to operate your unit, read the instructions in this manual thoroughly. Throughout this manual, you will

1-3 1.5 Equipment Description Pro H55 Series high-efficiency gas fryers employ a unique infrared burner system that uses up to 43% less energy to coo

1-4 QUALIFIED INSTALLATION PERSONNEL Qualified installation personnel are individuals, firms, corporations, and/or companies which, either in person

2-1 PRO H55 SERIES GAS FRYER CHAPTER 2: INSTALLATION INSTRUCTIONS 2.1 General Installation Requirements Qualified, licensed, and/or authorized ins